Product Description:

Corrmax is a single component, nano-architecture, clear top coating system designed to provide more than 5 years of surface durability in a single application and drastically cut down on-going maintenance needs with easy to clean surface properties.

Applications:

Corrmax is used across industries with heavy application across assets types in : Heavy industrial, Engineering Equipment Automobiles- Heavy, light Marine-Vessels, Infrastructure Construction, Architecture

Substrates:

Painted Surfaces-Alkyd, Polyurethane, Epoxy, Polyester, Acrylic, Latex, Powder Coat, E-coat, Gel Coat, others.
Metal- Milk Steel, Stainless Steel, Aluminium, Copper, Brass, others.

Benefits:

1-Durability of 5+ Years in a single application.
2-Environmental Protection for extreme gloss and colour retention.
3-Chemical and Corrosion Resistance
4-Physical Abuse Resistance (Dynamic Abrasion and Scratch)
5-Easy-to Clean Surface Properties
6-Single Component easy-to-apply coating
7-Great aesthetic finishes

Standards:

ASTM G115, ASTM G154, ASTM D4587, ASTM D3363, ASTM 34060 ASTM B117, ASTM D2794, ISO 2812-2, ASTM D4752

Form:

Appearance : Liquid, Colourless
Packaging: 1 Litre, 5 Litres, 20 Litres

Storage:

Store in a dry area at temperatures between 15-20 degree celsius (higher temperatures reduce shelf life) Shelf Life-6 months un-opened; 1 day once opened Container must be closed immediately after use to avoid contamination from moisture; discard if liquid turns white.

Technical Data

Chemical Base: Hybrid Polyurethane, Polyurea, Polysilane Specific Gravity: 0.984

Coating Properties

Weatherometer (Xenon, WOM)	100% Gloss Retention	(4000h, ASTM G115, SAE J1960)
QUV Resistance	100% Gloss Retention	(2000 h, ASTM D4587)
Salt Spray Test	No rust, no blisters	(2000 h, ASTM B117)
Pencil Hardness	4H Pass	(ASTM D3363)
Abrasion Resistance	8.4 mg	(ASTM D4060)
Impact Resistance	Pass: 27 joules	(ASTM D2794)
Flexibility	Pass ¼	(ASTM D522)
MEK Resistance	>1,500; Pass	(ASTM 4752)
Scrape Adhesion	0.25 kg (Scatch)>11 kg (Gouge)	(ASTM D2197)
Chip Resistance	7A	(ASTM D3170)
Falling Sand Abrasion	Pass	(ASTM D968, 100 litres)
Humidity/Moisture Resistance	No Effect	(500+ h, ASTM D4585, ASTM D714)

Coating Properties

Chemical Spot Resistance		(ASTM D1308)
10% Sulphuric Acid	No Effect
10% Hydrochloric Acid	No Effect
10% Sodium Hydroxide	No Effect
10% Ammonium Hydroxide	No Effect
Isopropyl Alcohol	No Effect
Xylene	No Effect
MEK	No Effect

Application Details:

Coverage:	180-220 sq.ft. per litre
Dust Free Time:	20 Mins (@25 o C, 50% R.H.)
Tack Free Time:	40 Mins (@25 o C, 50% R.H.)
Handlable Dry:	3 Hours (@25 o C, 50% R.H.)
Full hard Cure:	24 Hours (@25 o C, 50% R.H.)
Dry Film Thickness:	0.5 mil
Surface Preparation:	Corrmax is designed to be a permanent, covalently bonded coating if applied on well prepared surfaces: Complete degreasing of surface, coating will not adhere to surfaces with residues, impurities. 1000 grit sanding of surfaces is required for adherence of coating. Corrmax is designed to adhere to freshly coated surfaces as wet-on-wet application onto other coating system, when adequate time is provided for solvents to escape between coats. 1, 2 or 3 wet coats for wood, stone coating to be applied based on end application.

Application Details:

Application Equipment:	Air Spray- Spray Gun- HVLP, LVLP (1.3-1.5 mm nozzle) Pressure at Gun-29-30 PSI Airless Spray- Tip Size-Graco 519 or 619 orifice Pump-30:1 minimum Pump Pressure-55-60 PSI Application with rollers, lint free fabric, other pads possible- contact manufacturers for details. Clean equipment with thinner/acetone prior and post use
Surface Detailing/Finish (if required)	Use orbital saner to sand with 1000, 1500, 2000, 2500 gr it Sand papers sequentially. Use woolen buffing pad @ 1,200 to 1,400 rpm with a heavy/ extra cut compound. Go over as many passes as required to remove marks.

Safety: Refer to MSDS

The information, and, in particular, the recommendations relating to the application and end-use of our products, are given in good faith based on our knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with recommendations. In practice, the differences in materials, substrates and actual site conditions are such that fitness for a particular purpose must be tested for the intended application and purpose. Corrmax reserves the right to change the properties of its products. The proprietary rights to third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.